Old style ozone "plates" create large amounts of 
Nitrogen Oxides which are offensive, irritating, and dangerous.

Air-Zone's patented ozone elements are in a permanently molded housing, that require NO adjustment whatsoever. 
They also don't produce dangerous Nitrogen Oxides.

They can be easily cleaned with by using an air hose to blow out any dust. 

We use 24 carat gold plating on our elements internal components to help prevent corrosion. 
The use of high temperature, shatter resistant  tempered glass is also incorporated in our innovative ozone element design.

Old style ozone "plates" consist of  flimsy easily corroded steel screens and delicate thin pieces of glass or mica which must ALWAYS be in perfect alignment.
If not cleaned and aligned constantly, old style ozone "plates" will produce less ozone, and possibly even spark out dangerous high voltage electricity.

Air-Zone's patented ozone elements solve all these problems.

Our patented ozone elements can easily be cleaned by simply turning the ozone level up to full power for a few minutes, and burn any dirt off that has accumulated on them.

Old style ozone "plates", first designed in the 1800's,  must be removed, scrubbed clean, dried, and be meticulously reassembled, or they will not work correctly. Even with all that work, their life span is notoriously short.

Air-Zone's patented ozone elements last for years, are easily replaceable in minutes with a screwdriver.
They cost only $15-$20 each to replace.

Old style ozone "plates" typically cost $40.00 each or more.
Note that a competitors 10,000 mg.hr. unit would contain 10 of these $40.00 "plates" equaling $400.00

The Continuous mode allows for longer, or overnight applications.
It's smart chip remembers the timer setting last set even if the unit is unplugged!

Air-Zone uses completely sealed, high voltage transformers, that can withstand a lot of abuse before shorting out. They are designed specifically for our ozone generators.  Combined with our innovative ozone element design, it is very rare that one of our power transformers blow out.

Competitors use off the rack, open iron core transformers. The exposed iron can quickly rust and deteriorate. These types of transformers are not specifically designed for use in an ozone generator, and have a hard time maintaining a long life span in this type of machine.

Some companies use the same exact transformer in many different sized models.

Air-Zone uses multiple transformers in our different models.  How can a single transformer that is used in a small ozone machine be expected to handle the much higher load in a large ozone generator?

Many competitors machines simply use ONE transformer, the SAME EXACT transformer in many of their different low and high ozone output generator models.

Whether it be a single plate 1000 mg/hr model, a 5 plate 3600 mg/hr model, a 5 plate 5000 mg/hr model, or a 10 plate 10000 mg/hr model, some manufacturers use the same exact transformer in every machine.

How can the SAME transformer that is expected to handle one high voltage ozone element, handle ten high voltage ozone elements?

If a competitor states "Our transformer is so good we can use the same one in our low powered model as our high powered model" then what justifies the huge jump in price between the low and high powered models?
It seems to us they are just charging the customers empty dollars of more and more profits for increased ozone power.

That leads us to two possible conclusions: Either the transformer in the 10 plate 10,000 mg/hr model is woefully undersized, or 1000 mg/hr ozone generator is using a transformer that is already properly sized for a higher powered machine,

If the latter is the case, and the ozone plates are as low cost as they say, then why the huge price jump between lower and higher powered ozone generators?

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed. The load on the transformer HAS to be radically different on a single or five plate ozone generator. 

This is proven by the fact that when a competitor adds 4 more ozone plates to a 1000 mg/hr machine that the total ozone output does NOT equal 5000 mg/hr. 

The "upgraded" generator now only puts out 3600 mg/hr, the missing 1400 mg/hr of ozone output has been lost because the transformer has a hard time handling the different load.

That proves that the load is radically different when you simply add more ozone plates to a power transformer.  If the transformer has been strained so that it looses that much ozone power, then it can be concluded it is that much closer to straining and blowing out. 
It has to run at a higher temperature. 

So if competitors ozone plates are as cheap in cost as they say, and they use the same transformer in a 1000 mg/hr machine AND the 10,000 mg/hr machine, what justifies the more than $700.00 cost difference between the two models?

Our XT-2000 uses a single transformer. The XT-4000 uses 2 transformers. The XT-6000 uses 3 power transformers.  Our XT-14000 uses 6 power transformers and our XT-28000 uses 12 separate transformers.

We do this because to present a balanced load, and to have even power distribution. 
It is better to use multiple transformers when doubling or tripling the ozone power.
It only makes good sense. It makes for a more balanced ozone machine.

We don't just add two more ozone elements to the XT-2000 to make it a 4000 mg/hr machine.
The XT-4000 uses 2 separate transformers. Simply adding ozone elements isn't the proper solution.  Adding 2 more elements would NOT equal 4000 mg/hr. It might only increase the ozone power to 3200 mg/hr because the load presented to the transformer would be completely different.

That's why ozone generators that are "upgradable" by simply adding more ozone plates are not very well designed. The load on the transformer HAS to be radically different on a single or five plate ozone generator.

Keep in mind the fact that competitors also use ozone plate technology where each "plate" has 3 pieces in it that can easily move around.  They use a spring system to keep each part of the plate in perfect alignment. A 10 plate, 10,000 mg/hr ozone machine will have 30 separate pieces in its 10 ozone plates!  A 10,000 mg/hr "plate type" ozone machine has 30 parts that must ALWAYS be in perfect alignment or disaster will occur.

If a single piece of the glass or mica non-conductor breaks, cracks, or just slips out of alignment due to a lack of spring tension, then the electrical conductor, screen parts of the ozone elements can arc and cause an electrical short. 
When an ozone plate short outs, the transformer is also shorted out.  No matter how well it is built, a transformer cannot stand being shorted out for very long.  Electrical transformers cannot stand to have a high voltage, zero ohm load on them for very long without being put under a huge amount of strain.

Air-Zone not only uses multiple transformers in our higher powered units to help balance the load, they also use our U.S. patented ozone elements which do not have components in them that can move, or shift out of alignment. 
There is no way for them to short out as standard ozone plates can.

Don't buy the argument that using multiple transformers gives a machine more to break down. 
The truth is if properly sized transformers are used and not strained to capacity, there is very little change they will blow out.  Simply adding ozone plates as other manufacturers do, is what overloads electrical transformers and makes them more likely to blow out.

Our XT-14000 and our XT-28000 use special monitoring circuits, and indicator lamps on the front panel to always let the user know the status of each ozone element and transformer.
No other ozone generator made has that feature.
If a transformer ever blows the user will know about it right away. Because of these units modular construction this problem is very easy to fix.

Air-Zone are simply more stable ozone generators than most other brands.
Electronic protection circuits and fuses prevent our internal components from overload & burnout.